Search results

Image with ScannerMax C-506. In height (Y) all correct, but in width (X) very narrow. I have checked connections and I do not see anything strange. I send you the picture in case you can help. It is normal to have current continuity between GROUND (X), GROUND (Y), GROUND Stanwax board...

Hello friends. I have a G2 lens that came with a green module ND700 520nM / 700mW (Dave). My question is this lens also serves to 638nM? :pensando: Thank you. Best Regards. Juanma.

Hello everyone. Where I can buy an analog controller for Nichia NDG 520nm / 700mW? Best regards. Juanma.

Hello everyone. What filter (UV, ND4, CPL, ...) suitable for output galvos? Best Regards. Juanma.

Hi, friends. I'm looking for a power supply for galvos (PT-30/PT-40). And I do not find any with the features this type of source. (+ 24v / common / -24V). Three cables (red / black / yellow) to power amplifiers galvo. All I find are sources of 24v. But none with the possibility of + -24V using...

Hello, friends. That think about these scanners. Has someone proved them? Better that DT-40 pro? Best Regards. Juanma.

Hello friends. What other option is there to connect Ishow, and not use the PT-ITrust card ??? It ruined PT-ITrust ... I need another alternative to connect Ishow. Thank you. Juan Manuel.

Hello everyone. Which DAC for laser projector with ********* software you advise me, to replace my Ishow? I want to be economical, I can not spend too much money on it ... Best Regards. Juanma.

Hello everyone. I have a question ... How do I connect Galvo (3 pin) to amplifier output (2 pin)? Best Regards. Juanma.

Hey guys. I have a question. If I use USB Audio DAC + Amp mod Laserboy Correction, I use the TTL circuit of the laser module (image), or connect directly to the module? Best Regards. Juanma.

Hello. I have a problem with the projector, suddenly the images are shown very distorted (and seemingly bigger that before), it is not blame of Ishow neither of *********. I have been able to check that it also happens reproducing the predetermined images of the show card I-trust of the galvos...

Hello, friends. I Have C-Media Sound Card CM106 USB 2.0 - 5.1 ch. I want to know if I can connect the modules laser of my projector, without having to use The correction amp kit and to use in their place the controls of the modules that you can see in the following images. The adjustment...

Hello friends. Beginner's question. What beam is more divergence 445 or 470nm? Best Regards.

Hello. It is impossible to project image without twinkling, patron ILDA doesn't even show correctly. I have DAC Ishow, galvos 30k, software IShow and Noodles; blinks with all the graphics, I believe that the galvos doesn't move to the speed that these they allow. Graphics of presentation card...

Hi friends. Approximately... how many does mA have a module of 650nM/500mW? Thank you. Juanma.

Hello. These are my modules 532nm/50mW and 635nm/200mW. I want to know if I can to narrow of beam of the 635nm/200mW with some lens type or similar. Best Regards. Juanma.

Hello. As I connect this Mitsubishi diode? which is positive contact and the negative? Best Regards. Juanma.

Hello. I need to know the necessary components for laser show at home, "lost cost". Not I look for espectacularity, I want basic forms... beam, tunnel, beam splitters or beam combiners, different focus angles... and to move them to the music's rhythm. I have 3 modules (12v.) laser 3b class ...

Hello. I need to know the necessary components for laser show at home, "lost cost". Not I look for espectacularity, I want basic forms... beam, tunnel, beam splitters or beam combiners, different focus angles... and to move them to the music's rhythm. I have 3 modules (12v.) laser 3b class ...

Hello, of these two modules laser class 3b... 635-638nm 200mw Red Module/12V TTL Laser Moudle/Orange Red laser beam. http://www.ebay.es/itm/635-638nm-200mw-Red-Module-12V-TTL-Laser-Moudle-Orange-Red-laser-beam-/260896419409?pt=LH_DefaultDomain_0&hash=item3cbea36e51#ht_1754wt_1166 660nm 250mw...