Recent content by Rasser

Re: Lava Micro FlexDrive Driver (lavadrive2) fits Okey, I think I will sleep at the mailbox tonight if the post man should come with my drivers tomorrow :D

Re: Lava Micro FlexDrive Driver (lavadrive2) fits Mine was send the 24 Feb But I have not received them yet. Are there any who know how long it takes to send to other countries (Denmark) with "USPS First class shipping"?

Hmm then I dont think I understand the circuit, but that does nothing, when it works as it should ;) New drawing. Then it is like this? http://www.scrallar.dk/albums/userpics/10001/switch-on-dummy2.JPG When the switch is "on" it is the red I can measure And when the switch is "off" it is the...

Okey so I can do it like this http://www.scrallar.dk/albums/userpics/10001/switch-on-dummy1.JPG And when the switch is "on" it is the blu-ray I can measure And when the switch is "off" it is the red I can measure Is that right understood?

Hello. Can I make 2 contacts on my test load so I can switch between blu-ray and red? Or could it be I measure wrong then? Like this: http://www.scrallar.dk/albums/userpics/10001/switch-on-dummy.JPG

Heh yes, I have to translate the difficult words ;) Know I got the blu-ray diode out of the heatsink and in to the aixiz module :) I just got a extra question, As I told I was a little tough with the red diode/heatsink because I thought it was the IR diode. Can I try to connect it to a driver...

Crap, then I have smashed red diode because I thought it was the IR diode which I could not use to anything. It's because I looked ad "Bluray's" Tutorial "How to extract diode and Optics from 4X GBW-H10N" #1 IR diode #2 Centre Red long can diode #3 6XBR diode...

Hello, I purchased the GGW-H20L 6x BluRay Laser Diode sled, and dont know how I shall get the Heatsinks off the blu-ray and red diode I've tried a little to twist the Heatsinks off with pliers, but i can't... I am afraid to cut in the Heatsinks if there should come dust in/on the opening on...

Stupid me! Now I have tried with 2 x cr123 battery's, And I measure from 27mV to 436mV, And that should be right :) It is because I shall use the "Micro Flex Drive" when I get them (and they only use 1 x cr123) And then I had forgotten the rkcstr driver shall use 2 x cr123 batteries. I say...

Ohh that was why I could not measure anything. Yes it is set to red LD right now. I have tried as you have shown http://www.scrallar.dk/albums/userpics/10001/P1020040.JPG If I screw it all the way down it stands at 0.01 and if I screw it all the way up it stands at 0.26 How do I get that in...

Hello. It is my first time I built lasers, I have read and thought I had understood how to connect battery/driver/test load, but my DMM is just stands on 0.00 when I try to measure mA. So I must do something wrong :-[ Is there somebody that can draw posetiv and negative wire into my drawing...

Re: Lava Micro FlexDrive Driver (lavadrive2) fits Nice they are come in stock again, Now I just wait to receive the three I have preordered :D

Woow that is some really nice pictures you guys have taken! [smiley=thumbsup.gif]

Re: Where can I buy GGW-H20L 6x BluRay Laser Diode But I will remember it for next time ;)

Re: Where can I buy GGW-H20L 6x BluRay Laser Diode Hey, That sounds nice. But I have just purchased one of jayrob with his "pocket mini-kit".